The wooden panels can make a house welcoming and comfortable. However, if your home is full of panels that are old, damaged or made with lower quality veneer, it may be necessary to replace them. If you don’t have the budget necessary to remove them, you can consider the possibility of giving them a second young man thanks to the paint. It can immediately give these panels a modern aspect to the lowest cost.
How do you know if you have to paint the panels or not?
The question whether or not to paint the panels and the wooden moldings is a controversial subject. As for the cheap wooden veneer that was so popular in the 70s, the answer is almost universally «yes». When it comes to solid quality solid wood panels, the decision can be more complicated. First of all, it is impossible to go back, because it is practically impossible to completely smooth the panels of panels if you change your mind. On the other hand, solid wood plates have many seals that can open and present cracks if the panels contract during low humidity periods. If you decide to repair the panel of your home, follow the appropriate steps to make sure this is done in the rules of art. It may seem useless to clean, sand and apply a layer of primers, but the panels require particular attention if you want the support to be ready.
What you need to repair your panel
Equipment / tools
- Rag
- Sealing
- Silicone pistolet
- Paint roller with foam coating
- Brush
Material
- Marseille soap
- Wooden paste
- 150 gr glass paper
- Silicone
- Antitache primary
- Wall paint
- Finished paint
Instructions to paint the panel well
Clean forms and panels
Before trying to do anything with your wooden panels, be sure to clean them. A wet cloth will eliminate most of the canvases, dirty and spider. If there are layers of dirt, use an unsaponed solution and water to remove everything. Never paint on a dirty surface because the paint would not adhere correctly. It will also seem very neglected because the paint will collect land piles, which will make a flat and clean appearance impossible.
Fill and smooth the wood
Fill the holes or cracks with wooden stucco, using a sealing knife and let it dry. If you wish, it slightly smooth all the panels (without forgetting the outlines and moldings) with a glass card of 150 gr. The idea is to remove the lucid surface and create a slightly grainy surface so that the paint adheres well. Try not to let you transport and not to smooth too much. When you’re done, dry it with a slightly humid cloth to remove all the dust. Note: The sanding is optional and often useless. The use of a good primer that adheres to the old finish generally means that it is not necessary to smooth the wood. Remember that if the primer does not adhere well, the painting will not even do it. Sanding always improves adhesion.
Apply a mastic to paint
Apply the stucco to the spaces between wooden axes, between panels and fillings and around windows and doors. Make sure to use a «paint» stucco. Let the stucco dry according to the manufacturer’s instructions.
Apply the wood
Apply a thin layer of primer on all panels, using a sponge roller in foam and a brush or a alone. When you paint, keep a brush at hand to enter the cracks, the corners where the roller cannot go and to remove the drops. Make sure to cover the entire surface, including the contours. It is preferable to use an oil -based primer or a anticare primer based on water. This will prevent the passage and wooden stains from passing and damaging your painting.
Paint panels
Apply a thin layer of paint on all the surfaces of the panels. Start on the top and continue downwards, being careful to cover all the spaces between the panels. Remove the excess paint that accumulates in the grooves of the panels, using the brush. He also faces the possible drops immediately. Leave the first dry layer, as shown, then applies a second layer. After the primer and the first layer, the wall may appear finished, but a second layer will guarantee the best blanket and improve its sustainability. Time and additional materials are really worth it.
Paint the outline
Paint the desired color outline. It is generally preferable to use a brighter finish than you have chosen for the walls, but it is truly a matter of personal preference. A more lucid paint allows you to bring out the fillings and create a smoother and easier surface to clean.
Latest Posts Published
The challenges of ethical management and business management
What you need to know to modernize your space
Tips to improve the thermal insulation of the house
The economic and financial profits to invest in a twin house
How to discover the treasures of Byzantine art online?
The current challenges of urban properties in the face of the economic crisis of 2025
Effective suggestions for cleaning window cleaning
How to use it to accelerate growth?
Practical ideas and advice for a modern interior
